Verified 300-410 dumps Q&As - Pass Guarantee or Full Refund [Jul-2023]
300-410 PDF Dumps | Jul 13, 2023 Recently Updated Questions
Cisco is a leading provider of networking technologies and solutions, and the Cisco 300-410 exam is widely recognized as a valuable certification for network professionals. By earning this certification, network engineers can demonstrate their expertise and knowledge in advanced routing and services, and stand out in a competitive job market. Additionally, the CCNP Enterprise certification track provides a clear path for career advancement and professional development, enabling network engineers to grow their skills and expertise in enterprise networking.
Cisco 300-410 exam is a challenging test that covers a wide range of topics, including advanced routing protocols, VPN technologies, BGP, OSPF, and EIGRP. It also evaluates a candidate's knowledge of network services such as NAT, QoS, and multicast. Additionally, the exam assesses a candidate's ability to implement security features such as AAA, IPSec, and VPN. To succeed in the certification, candidates must have a deep understanding of networking concepts, protocols, and technologies, as well as practical experience in configuring and managing enterprise networks.
NEW QUESTION # 291
Refer to the exhibit.
Which action resolves the failed authentication attempt to the router?
- A. Configure aaa authorization console global command
- B. Configure aaa authorization login command on line vty 0 4
- C. Configure aaa authorization login command on line console 0
- D. Configure aaa authorization console command on line vty 0 4
Answer: A
Explanation:
In the debug output, we see that the Authorization (not Authentication) failed so we need to correct the authorization. In order to enable authorization, we must use the global command
"aaa authorization console" first.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/security/a1/sec-a1-cr-book/sec-cr-a1.html
NEW QUESTION # 292
Which method changes the forwarding decision that a router makes first changing the routing table or influencing the IP data plane?
- A. Nonbroadcast multi-access
- B. Packet switching
- C. Policy-based routing
- D. Forwarding information base
Answer: D
NEW QUESTION # 293
Refer to the exhibit.
During troubleshooting it was discovered that the device is not reachable using a secure web browser. What is needed to fix the problem?
- A. permit udp port 465
- B. permit tcp port 465.
- C. permit tcp port 443
- D. permit tcp port 22
Answer: C
NEW QUESTION # 294
A network administrator is tasked to permit http and https traffic only toward the internet from the User1 laptop to adhere to company's security policy. The administrator can still ping to www.cisco.com Which interface should the access list 101 be applied to resolve this issue?
- A. Interface G0/48 in the incoming direction
- B. Interface G0/0 in the outgoing direction.
- C. Interface S1/0 in the outgoing direction.
- D. Interface G0/0 in the incoming direction.
Answer: D
NEW QUESTION # 295
A newly installed spoke router is configured for DMVPN with the ip mtu 1400 command. Which configuration allows the spoke to use fragmentation with the maximum negotiated TCP MTU over GRE?
- A. ip tcp adjust-mtu 1360
crypto ipsec fragmentation mtu-discovery - B. ip tcp adjust-mss 1360
crypto ipsec fragmentation after-encryption - C. ip tcp adjust-mss 1360
crypto ipsec fragmentation mtu-discovery - D. ip tcp adjust-mtu 1360
crypto ipsec fragmentation after-encryption
Answer: B
Explanation:
https://www.cisco.com/c/en/us/support/docs/security/dynamic-multipoint-vpn-dmvpn/111976-dmvpn-troubleshoot-00.html
NEW QUESTION # 296
Refer to the exhibit.
R1 is being monitored using SNMP and monitoring devices are getting only partial information. What action should be taken to resolve this issue?
- A. Modify the access list to include snmptrap.
- B. Modify the access list to add a second line to allow udp any any eq snmp
- C. Modify the CoPP policy to increase the configured CIR limit for SNMP.
- D. Modify the CoPP policy to increase the configured exceeded limit for SNMP.
Answer: B
NEW QUESTION # 297
Refer to the exhibit.
An engineer has configured DMVPN on a spoke router. What is the WAN IP address of another spoke router within the DMVPN network?
- A. 192.168.1.4
- B. 172.18.46.2
- C. 192.168.1.1
- D. 172.18.16.2
Answer: B
NEW QUESTION # 298
Drag and drop the DHCP messages from the left onto the correct uses on the right.
Answer:
Explanation:
Explanation
DHCPACK
The server-to-client communication with configuration parameters, including committed network address.
DHCPINFORM
The client-to-server communication, asking for only local configuration parameters that the client already has externally configured as an address.
DHCPNAK
The server-to-client communication, refusing the request for configuration parameter.
DHCPDECLINE
The client-to-server communication, indicating that the network address is already in use
NEW QUESTION # 299
Which attribute eliminates LFAs that belong to protected paths in situations where links in a network are connected through a common fiber?
- A. lowest-repair-path-metric
- B. linecard-disjoint
- C. shared risk link group-disjoint
- D. interface-disjoint
Answer: C
NEW QUESTION # 300
What is a function of an end device configured with DHCPv6 guard?
- A. If it is configured as a relay agent, only prefix assignments are permitted.
- B. If it is configured as a client, only DHCP requests are permitted.
- C. If it is configured as a client, messages are switched regardless of the assigned role.
- D. If it is configured as a server, only prefix assignments are permitted.
Answer: C
Explanation:
Explanation
The DHCPv6 Guard feature blocks reply and advertisement messages that come from unauthorized DHCP servers and relay agents.
Packets are classified into one of the three DHCP type messages. All client messages are always switched regardless of device role. DHCP server messages are only processed further if the device role is set to server. Further processing of server messages includes DHCP server advertisements (for source validation and server preference) and DHCP server replies (for permitted prefixes).
If the device is configured as a DHCP server, all the messages need to be switched, regardless of the device role configuration.
NEW QUESTION # 301
Refer to the exhibit.
R5 should not receive any routes originated in the EIGRP domain. Which set of configuration changes removes the EIGRP routes from the R5 routing table to fix the issue?
- A. R4
route-map O2R deny 10
match tag 111
route-map O2R permit 20
!
router rip
redistribute ospf 1 route-map O2R metric 1 - B. R4
route-map O2R deny 10
match tag 111
!
router rip
redistribute ospf 1 route-map O2R metric 1 - C. R4
route-map O2R permit 10
match tag 111
route-map O2R deny 20
!
router rip
redistribute ospf 1 route-map O2R metric 1 - D. R2
route-map E20 deny 20
R4
route-map O2R deny 10
match tag 111
!
router rip
redistribute ospf 1 route-map O2R metric 1
Answer: A
Explanation:
In this question, routes from EIGRP domain are redistributed into OSPF (with tag 111) then RIPv2 but without any filtering so R5 learns all routes from both EIGRP and OSPF domain. If we only want R5 to learn routes from OSPF domain then we must filter out routes with tag 111 and permit other routes.
The line "route-map O2R permit 20" is important to allow other routes because of the implicit deny all at the end of each route-map.
NEW QUESTION # 302
Refer to the exhibit.
AS65510 iBGP is configured for directly connected neighbors. R4 cannot ping or traceroute network 192 168.100.0/24 Which action resolves this issue?
- A. Configure R4 as a route reflector server and configure R2 and R3 as route reflector clients.
- B. Configure R4 as a route reflector server and configure R1 as a route reflector client
- C. Configure R1 as a route reflector server and configure R2 and R3 as route reflector clients
- D. Configure R1 as a route reflector server and configure R4 as a route reflector client
Answer: B
NEW QUESTION # 303
Refer to the exhibit.
After redistribution is enabled between the routing protocols; PC2, PC3, and PC4 cannot reach PC1. Which action can the engineer take to solve the issue so that all the PCs are reachable?
- A. Set the administrative distance 100 under the RIP process on R2.
- B. Redistribute the directly connected interfaces on R2.
- C. Filter the prefix 10.1.1.0/24 when redistributed from RIP to EIGRP.
- D. Filter the prefix 10.1.1.0/24 when redistributed from OSPF to EIGRP.
Answer: D
NEW QUESTION # 304 
An engineer sets up a DMVPN connection to connect branch 1 and branch 2 to HQ branch 1 and branch 2 cannot communicate with each other. Which change must be made to resolve this issue?
- A. Option A
- B. Option D
- C. Option B
- D. Option C
Answer: B
Explanation:
Explanation
R1(config)#int tunnel 1R1(config-if) no ip split-horizon eigrp 100
NEW QUESTION # 305
Refer to the exhibit.
A network administrator configured an IPv6 access list to allow TCP return frame only, but it is not working as expected. Which changes resolve this issue?
- A. Option D
- B. Option A
- C. Option C
- D. Option B
Answer: C
Explanation:
Explanation
https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst3750/software/release/122_55_se/configuration/ e/scg3750/swv6acl.html
NEW QUESTION # 306
After some changes in the routing policy, it is noticed that the router in AS 45123 is being used as a transit AS router for several service provides. Which configuration ensures that the branch router in AS 45123 advertises only the local networks to all SP neighbors?
A)
B)
C)
D)
- A. Option A
- B. Option D
- C. Option B
- D. Option C
Answer: B
Explanation:
By default BGP advertises all prefixes to external BGP neighbors. This means that if you are multi-homed (connected to two or more ISPs) then you might become a transit AS. For example, ISP 2 in AS 200 can send traffic to your router in AS 100 to reach ISP 3 in AS 300 because you advertised prefixes in ISP 3 to ISP 2.
This is what will be seen in the BGP routing table of ISP1:
NEW QUESTION # 307
Refer to the exhibit. An engineer must establish multipoint GRE tunnels between hub router R6 and branch routers R1, R2, and R3. Which configuration accomplishes this task on R1?
A)
B)
C)
D)
- A. Option D
- B. Option B
- C. Option A
- D. Option C
Answer: B
NEW QUESTION # 308
Refer to the exhibit.
A network engineer receives a fault ticket about traffic drops from BANK SITE to BANK Users can reach BANK SITE Y from router RA as a source.
Routers RB and RD are acting as route reflectors.
Which configuration resolves the issue?
- A. RF(config)#router bgp 65201
RF(config-router)#neighbor 10.10.10.6 route-reflector-client - B. RC(config)#router bgp 65201
RC(config-router)#neighbor 10.10.10.2 route-reflector-client - C. RC(config)#router bgp 65201
RC(config-router)#neighbor 10.10.10.4 route-reflector-client - D. RB(config)router bgp 65201
RB(config-router)#neighbor 10.10.10.3 route-reflector-client
Answer: C
NEW QUESTION # 309
Refer to the exhibit.
Refer to the exhibit. When an FTP client attempts to use passive FTP to connect to the FTP server, the file transfers fail Which action resolves the issue?
- A. Modify FTP-SERVER access list to remove established at the end.
- B. Modify traffic filter FTP-SERVER in to the outbound direction.
- C. Configure to permit TCP ports higher than 1023.
- D. Configure active FTP traffic.
Answer: C
NEW QUESTION # 310
Drag and drop the SNMP attributes in Cisco IOS devices from the left onto the correct SNMPv2c or SNMPV3 categories on the right.
Answer:
Explanation:
NEW QUESTION # 311 
Refer to the exhibit. An engineer wanted to set a tag of 30 to route 10.1.80.65/32 but it failed.
How is the issue fixed?
- A. Modify prefix-list ccnp3 to add 10.1.64.0/20 ge 32.
- B. Modify route-map ospf-to-eigrp permit10 and match prefix-list ccnp2.
- C. Modify route-map ospf-to-eigrp permit 30 and match prefix-list ccnp2.
- D. Modify prefix-list ccnp3 to add 10.1.64.0/20 le 24.
Answer: C
Explanation:
Section: Mixed Questions
NEW QUESTION # 312
Refer to the exhibit.
The Internet traffic should always prefer Site-A ISP-1 if the link and BGP connection are up; otherwise, all Internet traffic should go to ISP-2 Redistribution is configured between BGP and OSPF routing protocols and it is not working as expected. What action resolves the issue?
- A. Set metric-type 2 at Site-A RTR1, and set metric-type 1 at Site-B RTR2
- B. Set OSPF cost 100 at Site-A RTR1, and set OSPF Cost 200 at Site-B RTR2
- C. Set OSPF cost 200 at Site: A RTR1 and set OSPF Cost 100 at Site-B RTR2
- D. Set metric-type 1 at Site-A RTR1, and set metric-type 2 at Site-B RTR2
Answer: D
Explanation:
Explanation
OSPF type 1 route is always preferred over a type 2 route for the same destination so we can set metric-type 1 at Site-A RTR1 so that it is preferred over Site-B RTR2.
Note:
Routes are redistributed in OSPF as either type 1 (E1) routes or type 2 (E2) routes, with type 2 being the default.
- A type 1 route has a metric that is the sum of the internal OSPF cost and the external redistributed cost.
- A type 2 route has a metric equal only to the redistributed cost.
- If routes are redistributed into OSPF as type 2 then every router in the OSPF domain will see the same cost to reach the external networks.
- If routes are redistributed into OSPF as type 1, then the cost to reach the external networks could vary from router to router.
NEW QUESTION # 313
How does LDP operate in an MPLS network?
- A. When topology changes occur such as a router failure, LDP generates peer discovery messages that terminate the LDP season to propagate an LSP change.
- B. When an adjacent LSR receives LDP discovery messages. TCP two-way handshake ensures that the LDP session has unidirectional connectivity.
- C. LDP notification messages allow LERs to exchange label information to determine the next hops within a particular LSP.
- D. Peer routers establish the LDP session, and the LDP neighbors maintain and terminate the session by exchanging messages
Answer: C
NEW QUESTION # 314
Refer to the exhibit.
Refer to the exhibit. The engineer configured and connected Router2 to Router1. The link came up but could not establish a Telnet connection to Router1 IPv6 address of 2001:DB8::1. Which configuration allows Router2 to establish a Telnet connection to Router1?
- A. permit ICMPv6 on access list INGRESS for Router2 to obtain IPv6 address
- B. jpv6 unicast-routing
- C. permit ip any any on access list EGRESS2 on Router1
- D. IPv6 address on GigabitEthernet0/0
Answer: D
Explanation:
--------------------------R1--------------------------------------------- interface Ethernet0/0 ip address 209.165.201.1 255.255.255.0 ip access-group EGRESS2 out ipv6 address 2001:DB8::1/64 end
----------------------R2-------------------------------------------------- interface Ethernet0/0 ip address 209.165.201.25 255.255.255.0 ipv6 address 2001:DB8::2/64 ipv6 address autoconfig ipv6 nd autoconfig default-route ipv6 nd cache expire 60 ipv6 nd ra suppress ipv6 traffic-filter INGRESS in end IOU_Router2#telnet 2001:DB8::1 Trying 2001:DB8::1 ... Open IOU_Router1>
------------------------------------------------------------------------------
NEW QUESTION # 315
Refer to the exhibit.
An engineer must configure PBR on R1 to reach to 10.2.2.0/24 via R3 AS64513 as the primary path and a backup route through default route via R2 AS64513. All BGP routes are in the routing table of R1. but a static default route overrides BGP routes. Which PBR configuration achieves the objective?
- A. Option D
- B. Option B
- C. Option A
- D. Option C
Answer: B
NEW QUESTION # 316
......
300-410 Exam Questions – Valid 300-410 Dumps Pdf: https://www.pass4surecert.com/Cisco/300-410-practice-exam-dumps.html
300-410 Practice Test Questions Answers Updated 530 Questions: https://drive.google.com/open?id=12EANrGHqDAhNmINDfvCBkkeRFl118MCz