108 Exam Questions for NCP-NS-7.5 Updated Versions With Test Engine
Pass NCP-NS-7.5 Exam with Updated NCP-NS-7.5 Exam Dumps PDF 2026
NEW QUESTION # 56
What does placing a policy in Monitor mode accomplish?
- A. Redirects discovered traffic to a monitoring device.
- B. Blocks traffic that does not match the policy.
- C. Visualizes discovered traffic that matches the policy.
- D. Enables hitlogs for traffic that matches the policy.
Answer: C
Explanation:
The most professional way to evaluate this question is to map the symptom to the Nutanix feature responsible for that function rather than reacting to secondary details in the prompt. The correct response is A, meaning
"Visualizes discovered traffic that matches the policy.". Monitor mode is designed for observation rather than enforcement. In Nutanix Flow, it discovers and visualizes matching traffic so an administrator can validate real application behavior before converting the policy to active enforcement. That is why the correct response focuses on visibility, not blocking. Policy hitlogs provide precise evidence of what Flow evaluated, including source, destination, protocol, and rule outcome. In troubleshooting, that makes hitlogs one of the best places to confirm whether traffic matched an allow or deny decision. This is a Flow policy design question, so categories, secured entities, rule direction, policy mode, and policy precedence matter more than simple IP connectivity assumptions. Notice that B does not fit because it targets a different layer of the Nutanix networking and security stack than the one causing the outcome here. C does not fit because it targets a different layer of the Nutanix networking and security stack than the one causing.
NEW QUESTION # 57
An administrator is deploying a multi-tier (web, app, database) application on a Nutanix cluster using AHV.
The administrator needs to allow internal communication between tiers and provide external access to the web tier. How should the administrator satisfy this requirement?
- A. Create a VPC with subnets for each tier and configure the Externally Routable Prefix to include only web subnets.
- B. Create separate VPCs for each tier and connect them to the same external NAT network and configure routing policies for inter-tier traffic.
- C. Create separate VLAN networks for each tier and configure routing on the physical network.
- D. Create a VPC with a single subnet and assign workloads of each tier to this subnet.
Answer: A
Explanation:
A reliable method here is to translate the scenario into Nutanix terms-VPC routing, external connectivity, policy scope, identity mapping, or upgrade readiness-and then choose the answer that directly addresses that domain. The correct response is D, meaning "Create a VPC with subnets for each tier and configure the Externally Routable Prefix to include only web subnets.". The winning option is the one tied to the native Nutanix object or control that governs the outcome described in the scenario. In lifecycle terms, Nutanix expects administrators to respect prerequisites, compatibility, and dependency order before enabling or upgrading Flow-related services. A strong exam habit is to ask which Nutanix construct would have to change for the symptom or requirement to change. That mental shortcut usually separates the real answer from distractors that mention generic networking steps, disruptive resets, or unrelated configuration objects. Notice that A does not fit because it targets a different layer of the Nutanix networking and security stack than the one causing the outcome here. B does not fit because it targets a different layer of the Nutanix networking and security stack than the one causing the outcome here. Seen operationally, the correct response is.
NEW QUESTION # 58
An organization plans to apply security controls based on user group membership in Active Directory. What configuration is required in Prism Central before VDI policies can be used?
- A. Configure category values mapped to AD groups.
- B. Create the list of users and assign categories to them.
- C. Assign categories to identities in the Admin Center.
- D. Map category assignments to roles using RBAC settings.
Answer: A
Explanation:
What makes this a strong certification question is that several answers look technically related, but only one aligns with the exact behavior of Flow networking or Flow security. The correct response is D, meaning
"Configure category values mapped to AD groups.". Identity-based controls in Flow depend on accurate mapping between Active Directory information and the categories or groups referenced by policy. If that mapping is wrong, the policy logic can be correct and access will still fail. This is a Flow policy design question, so categories, secured entities, rule direction, policy mode, and policy precedence matter more than simple IP connectivity assumptions. A strong exam habit is to ask which Nutanix construct would have to change for the symptom or requirement to change. That mental shortcut usually separates the real answer from distractors that mention generic networking steps, disruptive resets, or unrelated configuration objects.
Notice that A does not fit because it targets a different layer of the Nutanix networking and security stack than the one causing the outcome here. B does not fit because it targets a different layer of the Nutanix networking and security stack than the one causing the outcome here. For.
NEW QUESTION # 59
After creating a BGP session in Flow Virtual Networking, the session status remains down. Which log should an administrator use first in Prism Central to troubleshoot the issue?
- A. Network and Security event logs related to connectivity changes
- B. BGP Gateway system logs from the CVM
- C. Prism Central task execution logs
- D. Routing Protocol Logs for the specific BGP session
Answer: D
Explanation:
From a Nutanix exam perspective, this question is really testing whether the administrator understands the control point that actually governs the behavior shown in the scenario. The correct response is C, meaning
"Routing Protocol Logs for the specific BGP session". With BGP in Flow Virtual Networking, route exchange depends on both gateway objects and a correctly defined peering session. A healthy gateway alone is not enough; the session, peer parameters, and advertised prefixes must all align. Operationally, Flow Virtual Networking should be checked from the control plane outward: gateway health, peering state, route advertisement, ERP coverage, external path, and MTU when encapsulation is involved.
Notice that A does not fit because it targets a different layer of the Nutanix networking and security stack than the one causing the outcome here. B does not fit because it targets a different layer of the Nutanix networking and security stack than the one causing the outcome here. In practice, administrators who anchor their decisions to Prism Central constructs-such as VPCs, external networks, ERPs, categories, and policy modes-arrive at the correct answer faster and avoid unnecessary changes.
NEW QUESTION # 60
An administrator must delegate management of a single tenant VPC to a junior engineer. The engineer should be able to modify that VPC but must not see or change any other VPCs or networking configurations in Prism Central. The administrator wants to meet this requirement using RBAC. Which action should the administrator take to meet this requirement?
- A. Assign the VPC Admin role and restrict its scope to the desired VPC.
- B. Assign a Custom Role cloned from VPC Admin and restrict its scope to the desired VPC.
- C. Assign a Custom Role cloned from Network Infrastructure Admin and restrict its scope to the desired VPC.
- D. Assign the Network Infrastructure Admin role and restrict its scope to the desired VPC.
Answer: A
Explanation:
From a Nutanix exam perspective, this question is really testing whether the administrator understands the control point that actually governs the behavior shown in the scenario. The correct response is B, meaning
"Assign the VPC Admin role and restrict its scope to the desired VPC.". The winning option is the one tied to the native Nutanix object or control that governs the outcome described in the scenario. In practice, this falls into virtual network design: VPC structure, subnet type, external network behavior, routing intent, and address exposure are what determine the result. By contrast, A does not fit because it targets a different layer of the Nutanix networking and security stack than the one causing the outcome here. C does not fit because it targets a different layer of the Nutanix networking and security stack than the one causing the outcome here. Seen operationally, the correct response is the least disruptive and most deterministic one. It changes the exact Nutanix setting that governs the outcome instead of introducing workarounds elsewhere in the stack. A strong exam habit is to ask which Nutanix construct would have to change for the symptom or requirement to change. That.
NEW QUESTION # 61
An administrator wants to configure the subnet 10.1.1.0/24 to stretch across two VPCs over a Network Gateway in VXLAN mode. The VMs on this subnet need to communicate with a traffic pattern of size 2000 Bytes. What is the minimum MTU required in the underlay network to ensure communication happens without fragmentation or traffic drops?
- A. 2108 Bytes
- B. 9216 Bytes
- C. 2116 Bytes
- D. 2058 Bytes
Answer: D
Explanation:
From a Nutanix exam perspective, this question is really testing whether the administrator understands the control point that actually governs the behavior shown in the scenario. The correct response is A, meaning
"2058 Bytes". MTU planning matters because encapsulation adds overhead. When overlay, Geneve, VXLAN, or IPSec is present, a path that looks healthy at 1500 bytes can still fragment or drop larger frames unless the underlay and endpoints are sized correctly. In practice, this falls into virtual network design: VPC structure, subnet type, external network behavior, routing intent, and address exposure are what determine the result. By contrast, B does not fit because it targets a different layer of the Nutanix networking and security stack than the one causing the outcome here. C does not fit because it targets a different layer of the Nutanix networking and security stack than the one causing the outcome here. Seen operationally, the correct response is the least disruptive and most deterministic one. It changes the exact Nutanix setting that governs the outcome instead of introducing workarounds elsewhere in the stack. A strong exam habit is to ask which Nutanix construct would have to change for the symptom.
NEW QUESTION # 62
When creating a VPC, enabling the Transit VPC toggle changes the role of the VPC. What does the Transit VPC toggle do?
- A. Forces NAT for all external subnets
- B. Converts all Overlay subnets into VLAN subnets
- C. Creates a hub-and-spoke VPC for routing
- D. Enables DHCP relay for routed subnets
Answer: C
Explanation:
The clean way to read this scenario is to separate what is merely present in the environment from the single Nutanix construct that actually satisfies the requirement. The correct response is B, meaning "Creates a hub- and-spoke VPC for routing". A Transit VPC acts as the routing hub for spoke VPCs and is commonly used when administrators want shared services or inter-VPC communication without pushing route complexity into the physical network. In practice, this falls into virtual network design: VPC structure, subnet type, external network behavior, routing intent, and address exposure are what determine the result.
In other words, this is less about broad infrastructure suspicion and more about finding the exact Nutanix decision point that explains the behavior. Notice that A is not appropriate because NAT changes addressing behavior and does not solve the routing or policy condition described in the scenario. C does not fit because it targets a different layer of the Nutanix networking and security stack than the one causing the outcome here.
Seen operationally, the correct response is the least disruptive and most deterministic one. It changes the exact Nutanix setting that governs the outcome instead of introducing workarounds elsewhere in the stack.
NEW QUESTION # 63
What happens when a monitored policy is enforced?
- A. Removes all discovered flows
- B. Deletes the policy hitlogs
- C. Stops logging traffic
- D. Blocks all traffic that is not allowed
Answer: D
Explanation:
What makes this a strong certification question is that several answers look technically related, but only one aligns with the exact behavior of Flow networking or Flow security. The correct response is B, meaning
"Blocks all traffic that is not allowed". Policy hitlogs provide precise evidence of what Flow evaluated, including source, destination, protocol, and rule outcome. In troubleshooting, that makes hitlogs one of the best places to confirm whether traffic matched an allow or deny decision. This is a Flow policy design question, so categories, secured entities, rule direction, policy mode, and policy precedence matter more than simple IP connectivity assumptions. By contrast, A does not fit because it targets a different layer of the Nutanix networking and security stack than the one causing the outcome here. C does not fit because it targets a different layer of the Nutanix networking and security stack than the one causing the outcome here. The key takeaway is that Flow is intentionally modular. Networking objects determine reachability, security objects determine permission, and lifecycle steps determine supportability. Mixing those layers usually produces the distractor answers. A strong exam habit is to ask which Nutanix construct would have to.
NEW QUESTION # 64
A new multi-tier application is being deployed across several subnets in a Nutanix environment. The security team wants to create a Flow Network Security Policy to restrict traffic between the tiers, but the complete matrix of required network ports and protocols is not fully documented. Which strategy should the team employ first to accurately capture the necessary communication patterns without risking application outage?
- A. Apply a Security policy in Monitor mode to discover all traffic between the application tiers.
- B. Create broad Security Policy to permit all TCP traffic between the tiers to ensure connectivity.
- C. Apply a Security Policy in Enforce mode adding the required flows as they appear in the flow logs.
- D. Create an IPFIX export of all the application traffic and monitor all traffic for 48 hours.
Answer: A
NEW QUESTION # 65
An administrator has configured two VPCs with overlapping externally routable prefixes (ERPs). The two VPCs are associated to separate external networks that are part of the same physical routing domain. What outcome should the administrator expect?
- A. Routing conflicts and unreachable external paths
- B. NAT is always automatically enforced
- C. Prefixes are merged into a single advertised route
- D. The larger prefix takes priority automatically
Answer: A
Explanation:
The clean way to read this scenario is to separate what is merely present in the environment from the single Nutanix construct that actually satisfies the requirement. The correct response is A, meaning "Routing conflicts and unreachable external paths". Externally Routable Prefixes determine which overlay prefixes are advertised beyond the VPC. If the ERP does not cover the workload subnet, upstream devices never learn a valid return path, even when the local VPC appears healthy. Operationally, Flow Virtual Networking should be checked from the control plane outward: gateway health, peering state, route advertisement, ERP coverage, external path, and MTU when encapsulation is involved.
In other words, this is less about broad infrastructure suspicion and more about finding the exact Nutanix decision point that explains the behavior. Notice that B is not appropriate because NAT changes addressing behavior and does not solve the routing or policy condition described in the scenario. C does not fit because it targets a different layer of the Nutanix networking and security stack than the one causing the outcome here.
Seen operationally, the correct response is the least disruptive and most deterministic one. It changes the exact Nutanix setting that governs the outcome instead of introducing workarounds elsewhere in the stack.
NEW QUESTION # 66
A customer wants to extend a VLAN subnet to a remote data center using VTEP. The administrator configures a Subnet Extension which shows UP in the Prism Interface, yet traffic fails to pass. Which setting is most likely misconfigured?
- A. VXLAN UDP port is set to 4789.
- B. VLAN ID does not match in the remote data center.
- C. Route Policy for VTEP has not been configured.
- D. Remote gateway IP address has not been configured.
Answer: B
Explanation:
What makes this a strong certification question is that several answers look technically related, but only one aligns with the exact behavior of Flow networking or Flow security. The correct response is B, meaning
"VLAN ID does not match in the remote data center.". The winning option is the one tied to the native Nutanix object or control that governs the outcome described in the scenario. Operationally, Flow Virtual Networking should be checked from the control plane outward: gateway health, peering state, route advertisement, ERP coverage, external path, and MTU when encapsulation is involved. A strong exam habit is to ask which Nutanix construct would have to change for the symptom or requirement to change. That mental shortcut usually separates the real answer from distractors that mention generic networking steps, disruptive resets, or unrelated configuration objects. Notice that A does not fit because it targets a different layer of the Nutanix networking and security stack than the one causing the outcome here. C does not fit because it targets a different layer of the Nutanix networking and security stack than the one causing the outcome here. For exam preparation, remember that Nutanix usually separates discovery.
NEW QUESTION # 67
An administrator has configured a VPC with multiple overlay subnets and attached a VPN gateway using IPSec. After enabling Jumbo Frames on the physical network, VMs are still experiencing packet drops. What is the most likely reason?
- A. Floating IP is missing on the VPN gateway.
- B. MTU on guest VMs exceeds recommended size for IPSec.
- C. Jumbo frames are not supported on overlay subnets.
- D. DHCP relay is misconfigured.
Answer: B
Explanation:
This item is best solved by thinking like an operator in Prism Central: first identify whether the problem is design, control-plane state, or policy logic, then pick the option tied to that layer. The correct response is A, meaning "MTU on guest VMs exceeds recommended size for IPSec.". A Floating IP is the normal mechanism for exposing a workload in an overlay-backed VPC to external clients. It preserves internal VM addressing while publishing a reachable external address through the VPC's north-south path. A VPN showing an "Up" state confirms tunnel establishment, but it does not guarantee end-to-end reachability.
Actual traffic flow still depends on route advertisement or static routing, proper prefixes, and correct MTU considerations. Operationally, Flow Virtual Networking should be checked from the control plane outward:
gateway health, peering state, route advertisement, ERP coverage, external path, and MTU when encapsulation is involved. By contrast, B does not fit because it targets a different layer of the Nutanix networking and security stack than the one causing the outcome here. C does not fit because it targets a different layer of the Nutanix networking and security stack than the one causing the outcome here. For exam.
NEW QUESTION # 68
While configuring third-party services (Service Insertion) in Flow Network Security Next-Gen, an administrator notices dropped packets when redirecting traffic through a network function. Which configuration change would address this issue?
- A. Reduce the MTU size to 1400 to match Geneve encapsulation.
- B. Increase the MTU by an additional 58 bytes for the Geneve header.
- C. Disable Geneve tunneling on the virtual switch.
- D. Keep the default MTU at 1500. Encapsulation is handled automatically.
Answer: B
Explanation:
The most professional way to evaluate this question is to map the symptom to the Nutanix feature responsible for that function rather than reacting to secondary details in the prompt. The correct response is C, meaning
"Increase the MTU by an additional 58 bytes for the Geneve header.". MTU planning matters because encapsulation adds overhead. When overlay, Geneve, VXLAN, or IPSec is present, a path that looks healthy at 1500 bytes can still fragment or drop larger frames unless the underlay and endpoints are sized correctly.
Service insertion introduces an additional dataplane hop through a network function VM. That makes correct vNIC pairing, health monitoring, and MTU sizing essential, because steering can fail even when the firewall appliance itself appears powered on. This is a Flow policy design question, so categories, secured entities, rule direction, policy mode, and policy precedence matter more than simple IP connectivity assumptions. In other words, this is less about broad infrastructure suspicion and more about finding the exact Nutanix decision point that explains the behavior. Notice that A does not fit because it targets a different layer of the Nutanix networking and security stack than the one causing the outcome.
NEW QUESTION # 69
An administrator has been tasked with creating a security policy to protect specific virtual network interfaces (vNICs) within a VM in a Flow Virtual Networking setup. How can the administrator ensure that only a specific vNIC is protected by the policy?
- A. Configure an entity group with a VM and a subnet, and apply the policy to the entity group, including categories for both VM and subnet.
- B. Create a general policy for all vNICs and assign it to the VM. The system will automatically select the vNIC to protect.
- C. Use subnet categorization to create a vNIC-specific policy, securing the selected vNIC based on its associated subnet.
- D. Apply the policy to the VM, and then use network segmentation to isolate the vNIC.
Answer: C
Explanation:
A reliable method here is to translate the scenario into Nutanix terms-VPC routing, external connectivity, policy scope, identity mapping, or upgrade readiness-and then choose the answer that directly addresses that domain. The correct response is B, meaning "Use subnet categorization to create a vNIC-specific policy, securing the selected vNIC based on its associated subnet.". The winning option is the one tied to the native Nutanix object or control that governs the outcome described in the scenario. This is a Flow policy design question, so categories, secured entities, rule direction, policy mode, and policy precedence matter more than simple IP connectivity assumptions. By contrast, A sounds plausible, but it does not align with the specific Flow policy object or precedence rule that controls this case. C sounds plausible, but it does not align with the specific Flow policy object or precedence rule that controls this case. For exam preparation, remember that Nutanix usually separates discovery from enforcement, routing from NAT, and access policy from identity mapping. Choosing the layer that truly owns the function is what leads to the right answer. A strong exam habit is to ask which Nutanix construct would have to change for.
NEW QUESTION # 70
In a Nutanix deployment, when is the Network Controller automatically enabled?
- A. When the Network Controller is enabled on a Hyper-V cluster
- B. When the Small Prism Central deployment is scaled out to three PCVM's
- C. When the Network Controller is manually configured from the Prism Central settings page
- D. When the X-Large Prism Central deployment is installed or upgraded
Answer: B
NEW QUESTION # 71
An enterprise has deployed a VPC called FinanceVPC using Nutanix Flow Virtual Networking. The Finance team needs the following connectivity: Internal servers in the VPC must reach an on-premises corporate data- center via a point-to-point encrypted link. Some servers in the VPC must also access the public internet with source NAT and receive inbound access via floating IPs. The corporate network uses overlapping IP space with other VPCs in the environment, so address translation is necessary for those workloads. The networking design must support routing via BGP for future site expansions and provide low-latency north-south connectivity. Which actions should the administrator take to satisfy this requirement?
- A. Use two No-NAT External Networks-one for the on-prem link and one for Internet access; configure static routes for both without NAT.
- B. Use a single No-NAT External Network for both on-prem and Internet access; configure BGP and direct routing out to the internet without NAT.
- C. Use a single NAT External Network for both the on-prem link and Internet access; configure a default route to the external network and enable SNAT and floating IPs for all traffic.
- D. Use a No-NAT External Network for the on-premises link and a NAT External Network for Internet access. Configure a VPN tunnel to the on-premises location and enable BGP on the VPC router for the on-premises link.
Answer: D
Explanation:
The most professional way to evaluate this question is to map the symptom to the Nutanix feature responsible for that function rather than reacting to secondary details in the prompt. The correct response is C, meaning
"Use a No-NAT External Network for the on-premises link and a NAT External Network for Internet access.
Configure a VPN tunnel to the on-premises location and enable BGP on the VPC router for the on-premises link.". A Floating IP is the normal mechanism for exposing a workload in an overlay-backed VPC to external clients. It preserves internal VM addressing while publishing a reachable external address through the VPC's north-south path. Externally Routable Prefixes determine which overlay prefixes are advertised beyond the VPC. If the ERP does not cover the workload subnet, upstream devices never learn a valid return path, even when the local VPC appears healthy. In practice, this falls into virtual network design: VPC structure, subnet type, external network behavior, routing intent, and address exposure are what determine the result. A strong exam habit is to ask which Nutanix construct would have to change for the symptom or requirement to change. That mental shortcut usually separates the real.
NEW QUESTION # 72
An administrator has been tasked with upgrading the Nutanix cluster to a newer version of AOS. The cluster is running a mix of different versions across nodes... What is the recommended first step when upgrading a Nutanix cluster with different AOS versions across nodes?
- A. Upgrade the Nutanix Controller VMs first to ensure compatibility with the new AOS version.
- B. Upgrade the entire cluster at once to minimize downtime and ensure consistency.
- C. Upgrade all nodes to the same version of AOS before proceeding with any other components.
- D. Begin by upgrading the storage and network components to the latest version before upgrading the controller VMs.
Answer: C
Explanation:
What makes this a strong certification question is that several answers look technically related, but only one aligns with the exact behavior of Flow networking or Flow security. The correct response is B, meaning
"Upgrade all nodes to the same version of AOS before proceeding with any other components.". The winning option is the one tied to the native Nutanix object or control that governs the outcome described in the scenario. In lifecycle terms, Nutanix expects administrators to respect prerequisites, compatibility, and dependency order before enabling or upgrading Flow-related services. A strong exam habit is to ask which Nutanix construct would have to change for the symptom or requirement to change. That mental shortcut usually separates the real answer from distractors that mention generic networking steps, disruptive resets, or unrelated configuration objects. Notice that A does not fit because it targets a different layer of the Nutanix networking and security stack than the one causing the outcome here. C does not fit because it targets a different layer of the Nutanix networking and security stack than the one causing the outcome here. That is the underlying Nutanix principle being validated: solve the issue at the.
NEW QUESTION # 73
An administrator receives a ticket reporting unwanted traffic between production and development servers.
The administrator reviews the Flow Network Security logs and finds the following:
How can the administrator resolve the issue?
- A. Update the policy to disallow the unwanted traffic.
- B. Enable the Network Controller for the policy
- C. Change the enforcement mode for the policy
- D. Move the servers to separate IP subnets.
Answer: A
Explanation:
What makes this a strong certification question is that several answers look technically related, but only one aligns with the exact behavior of Flow networking or Flow security. The correct response is A, meaning
"Update the policy to disallow the unwanted traffic.". The Network Controller supplies the control-plane services required for Flow Virtual Networking. Without it, Prism Central cannot build and manage overlays, gateways, and related virtual networking constructs consistently across the cluster. From a troubleshooting standpoint, the validation path is policy scope first, then categories or identity mapping, then hitlog evidence, service definition, and finally policy precedence. A strong exam habit is to ask which Nutanix construct would have to change for the symptom or requirement to change. That mental shortcut usually separates the real answer from distractors that mention generic networking steps, disruptive resets, or unrelated configuration objects. Notice that B does not fit because it targets a different layer of the Nutanix networking and security stack than the one causing the outcome here. C sounds plausible, but it does not align with the specific Flow policy object or precedence rule that controls this case. The key takeaway is that Flow is intentionally.
NEW QUESTION # 74
......
NCP-NS-7.5 Exam Dumps - Free Demo & 365 Day Updates: https://www.pass4surecert.com/Nutanix/NCP-NS-7.5-practice-exam-dumps.html
Free Sales Ending Soon - Use Real NCP-NS-7.5 PDF Questions: https://drive.google.com/open?id=1s8xBKvEL_8vZMvHpWKufeJgKa4FaJOUk